No Products in the Cart
We should always do the steps by polish-shampoo-cleanser-coat-wax!
Bullsone crystal coat acts like a sealant to maintain the deep gloss of you original paint (Bullsone crystal coat also contains water repellant effects to reduce future water marks and stains stucked) , and once the deep gloss of original paint is achieved you can wax to prevent sun damage like discolouring and oxidation.
Bullone crystal series PH balanced car wash shampoo will ensure the surface remains at a neutral pH of 7 while other, more caustic, cleaners will leave a basic or acidic surface which might even strip your existing car coating! Using a non PH Balanced car wash shampoo will also affect the tone and color of your car after coating and waxing!
1. Start the engine and turn OFF the air-conditioner. Set the fan to maximum, and the air circulation system to internal circulation.
2. Place the can on a flat surface in the center of the floor mat on the passenger seat.
3. Tear the water pouch incision part, pour water into the container, and close all doors on the vehicle.
4. After 10 minutes, remove the product container, and ventilate the car to eliminate the smoke completely.
Periodic car wash plays an important role not only in the cleanliness of the vehicle, but also on durability. It depends on the climatic condition and tendency of the car owner, but it is recommended to wash the car regularly every 2 to 3 weeks. When the car is exposed to snow, rain, yellow dust, fine dust and also calcium chloride in the winter, these pollutants should not be neglected, and must be removed immediately.
There are various methods in the order of car wash, but we recommend for you to follow the order listed below.
1. Pre-wash: High-pressure water is used to wash the car as if sweeping from the top to bottom. Before using the managing agent, sand, dirt and thick foreign substances must be removed, and pre-wash has the effect of cooling the car surface.
2. Bubble Washing (Foam Gun & Foam Lance, Mitt Use): Bubble is sprayed by using the foam gun or foam lance, and to be left on the car surface for 3 to 5 minutes before using the mitt to wash the polluted areas of the car.
* Recommended Products: Spray-type washing (Crystal Car Shampoo, Firstclass Fomaing Car Shampoo), Car washing using Bucket/Foam Gun/Foam Lance (Crystal Bubble Car Wash Shampoo), Car Wash Products (Bullsone Car Wash Sponge)
3. High-pressure washing: Pollutants and remaining bubbles on the coating surface, glass, wheel and wheel house are removed, and bottom washing is also possible if there is bottom washing function.
In the winter season, bottom washing is very important because the deicers such as calcium chloride can cause corrosion.
4. Drying: After removing the moisture on the gap, drying towel is used to remove the moisture from the coating surface and glass, etc.
* Recommended Products: Bullsone Microfiber Towel Series (Large size, Basic Cleaning towel, Cleaning towel set(3 types))
5. Cleaning & Coating: Compound is used to manage the scratches and paint spots, and coating surface gloss coating and tire gloss products are used for car management.
* Recommended Products: Compound (Crystal Compound, Firstclass 2-Step Compound, Firstclass 3-Step Compound mini-kit, etc.),
Coating Surface Gloss & Water repellent (Crystal Coat Plus)
Tire & Wheel care (Crystal Wheel Cleaner, Crystal Tire Coat)
6. Car Interior Wash: High-pressure gun or vacuum cleaner is used to remove the dust from the mat, dashboard, air vent and seats to manage the pollution and gloss of the interior.
* Recommended Products: Crystal Interior Cleaner, Crystal Glass Cleaner, Carejam Leather Cleaner, Lotion, 2-Step Leather Care, etc.
Tires are exposed to various pollutants repeatedly, and if they are not managed regularly, the rubber is deteriorated to result in discoloration.
Exclusive tire cleaner is used to wash the tire before having any pollutants removed, and exclusive coating & gloss product can be used to not only extend the tire life, but also to have gloss effect.
* Recommended Products: Crystal Tire Coat, Firstclass Tire Shine Protectant, Tire Shine, Wheel & Tire 2 in 1 Cleaner, etc.
The results may vary depend on usage.
There are customers who visit the car service center to replace the wiper, or think that replacing the wiper is troublesome and difficult.
But you can actually replace the wiper easily and conveniently through the following methods in order.
First, raise the locking device on the center of the wiper to release.
Second, separate the product from the wiper ring.
Third, release the locking device of the new product.
Fourth, insert the ring to fix the wiper.
Fifth, remove the wiper blade cover to finish the installation.
When the following signs are shown, the wiper needs to be changed.
First, the wiper does not wipe the glass properly, and there is a dragging phenomenon.
Second, friction sound is heard when the wiper is moving, in contact with the glass.
Third, the wiper seems to bounce on operation.
In addition, when there is a oil film on the front glass due to dust and exhaust gas, the above problems cannot be solved just by changing the wiper. In this case, we recommend oil film removal and water-repellent coating before changing the wiper.
For the water repellent wiper, coating film is discharged from the wiper to prevent the rain drops from gathering and just to bounce the water drops off. Unlike the general wipers, the hybrid wiper has joint structure to have good contact with the glass for outstanding wiping performance.
The difference of the two products is the wing.
The Metal Hybrid Wiper has the metal frame and 4 joints in the structure to have strong contract to the glass, and even the ends of the wiper shows clean wiping performance.
The Metal Wing Hybrid Wiper is equipped with a dynamic wing on the Metal Hybrid Wiper, and maximum contact and wiping performance can be achieved even in high-speed driving of 180km/h.
Like a house that must have good basic frame to be a good house, the wiper must also have a good frame.
Unlike other plastic wipers, Bulls One Hybrid Wiper is made of metal material to have proper weight.
The frame is made of metal to give excellent pressing power, and the wiper is in good contact with the glass surface on rainy or windy days to wipe the glass better than other products.
The effective duration of the water-repellent coating products may vary depending on the environment, but coating by RainOk Extreme Rain Repellent lasts for about 6 months.
RainOk Clean & Rain Repellent 2in 1 : 1 week or more
RainOk Extreme Rain Repellent - For Side Mirror: Max. 1 day (24 hours) ~ 1 week
RainOk Speed Spray: 2 weeks
RainOk Rain Repellent Tisuse: 2 ~ 4 hours on rainy days, 2 ~ 4 weeks on sunny days
Before using the product, stain or dust on the glass surface must be removed and dried completely.
Bullsone Grasse range features 100% Essential Oil from France, 0% chemicals!